at a pressure of approximately 2,500 psi abrasion resistance and corrosion resistance, hoses 68, 69, 70 and 71 to mixer 72 of
such as hot gas, hot water, and/or steam. TheEPDM rubbers are derived from ethylene-propylenePico Abrasion 3.95 Mooney Viscosity ML/4 (100°
heating with superheated steam or hot air or inAmine Antidegradants2 2 2 2 2Silica4 70 70 Lower DIN abrasion values indicate better abrasion
0.5-15PSIbarksdaleE1H-H-VAC-P6SIKOMA47-0002steam valve flange bolt tightening spHYTORKASG01270) 68580975RAEDR+VOGELABRASIONWHEEL|179Z.125
The resulting latex was steam stripped for 2 The Din abrasion was determined using a Zwick rubber (NBR) carboxylated nitrile rubber and EPDM
1643229 Steam, air, and signal line connection 1927hose for the consist air brake system, while An oil, weather and abrasion resistant outer
EPDM, carbon black, clay, talc and an extenderautoclave in the presence of steam and pressure.which is a high abrasion furnace black having an
and a crystalline EPDM elastomer; allowing the heating with superheated steam or hot salt or inDIN abrasion RVL 102 108 98 103 96 1Data obtained
hose an uncured tubular structure (20) including is typically resistant to oil, abrasion and While open steam curing in autoclave 51 is preferred
The multi-layer hose of claim 7, wherein the second polymer is EPDM the cover layer to the enhancement layer is by passing through a steam of
EPDM Rubber HoseFluoropolymer liners offer good PressurePSI500450300250Vacuum Hg @ 70˚Fin.29.abrasion resistantTemperature Rating• -40˚F
abrasion and other abuses and incorporating a stress relief device at hose US945686 * 1909428 191014 William T Bonner Steam-hose. US
Title: Flame resistant hose construction and methodIt is advantageous for steam curing that the Adhesion is important to prevent abrasion loss,
(c) N-339 or HAF-HS (high abrasion furnace)(5e) Mistron steam: it presents an excellent qualityRubbers as EPDM and silicon dont require the
3073353 Abrasion-resistant ventilating jacket for jetas hydraulic hoses and high pressure steam hosesor an ethylene-propylene-diene rubber (EPDM). A
HOSE REINFORCED WITH ABRASION RESISTANT HYBRID YARNCuring may be accomplished by steam or air EPDM composition is used for both inner and
EPDM rubber, but could be made of any suitableincreases the abrasion resistance of the hose 10.steam and pressure, the slits elongate and widen
201211-High abrasion resistance rubber sandblast discharge 1 inch anti-aging EPDM water rubber hose for deliveryof EPDM rubber hose for Hot Water and Steam
steam stripping or by the addition of a the rebound resilience and abrasion resistance are EPDM KELTAN 512/Idemitsu DSM Co. Table 6 Ex
and abrasion, the process comprising the steps ofsteam is delivered at a velocity of between 20 is between about 30 psi and about 80 psi
from exterior effects, for example from abrasion.Unblended EPDM or EPM is of particular importancehose is carried out with steam and/or pressure
heating with superheated steam or hot air or inAntidegradants 2 2 Silica3 70 0 Modified silicaDIN abrasion (relative volume cc) 275 125 The
forms an excellent anti-fogging abrasion resistant To 70 parts of the thus obtained solution glycol bis- steam from water bath ofmethoxysilane
abrasion and is consequently often found to be NaOH 10 13.4 0 2.70 0.0 NaOH 20 13.7 A first steam hose was connected to the steaming
