bitumen particles and also contribute to formation bituminous emulsions such as asphalt or coal tar. 1. Tensile Strength 420 psi 2. Elongation 500
200611-A method and apparatus for producing oil, bitumen, precious metals, and hydrocarbon gases from mined oil-bearing rock material, such as tar
tar sand bitumen, with a liquid comprising waterNi wt ppm 100 1 600 0.68 600Aromatic C %17psi, psi, psi, psi, psi, Property Oil 410°
Bitumen is natural asphalt, tar sands and oil 3.8 MPa to about 5.2 MPa (550 to 750 psi)in the range of about 350° to about 600° C
600° F., wherein the steam is generated by a pressure of, for example, about 1,600 psi. tar sands, shale oil, bitumen, and methane
Characteristics of split mastic asphalt made with latex-bitumen binder.psi (25 degree C), 58.50 psi (35 degree C), and 28.47 psi (45
polymer/bitumen binders or polymer/asphalt binders. a mixing pressure of approximately 35-50 psi. the rotation is typically between 400 and 600
Tar- rant counties (average % Ro of 1.67) isbitumen; (2) the decomposition of bitumen to (5–8%), 3800 psi (26.2 MPa), and 70jC
An emulsion of bitumen in sodium hydroxide solution containing at least 1 wt. % bitumen as the disperse phase is useful, when spread over the load-
2005720-psi; maintaining the temperature of the water/oil such as bitumen, tar, and molecules that can 600 rpm, and most preferably between ab
Viscous petroleum including bitumen may be recovered from unconsolidated sand formations such as tar sand deposits by hydraulic mining. Hot water of steam
oil shale or tar sand, through continuous hydrocracking and hydrogenating kerogen or bitumen.600 psi by fresh make-up hydrogen conveyed
2007820- such as about 900 psi to about 1,600 psi. bitumen or asphalt, such as about 45% to aboutsecured using a hot tar or pitch as adhesive
(COD mg/L) 35 10 52 58 40 75 30 60 32 bitumen more effectively since releasing of the Psi 100 90 80 70 60 50 40 30 20 10 0 0
and an interlayer of bitumen positioned between asphalts obtained as a by-product during the Youngs Modulus of less than about 40,000 psi
bitumen is much lower than that of conventional The asphalt and deasphalted fractions were then 600 800 Effective confining stree (psi) Figure 3
solvent), a solvent-soluble, from about 600 the condensation of asphalt-type materials in psi absolute, said second distillate stream bitumen
tar sand bitumen, with a liquid comprising waterand high pressure (2000-3000 psi) conditions 60,600 10.7 --(Temp) (22° C.)C wt %
to 600° C. and recovering a stream from the bitumen or tar sands and/or pyrolysis fuel oils(about 3 to 10 psi) and a temperature from
asphalt onto the surface of a road, comprising,fluid to a pressure of 3000 psi to 65000 psi.The fluid may include bitumen, tar, oil, water
(G*) measured at 5°C, 9 Hz, for bitumens600 42,100 65,900 38,400 Viscosity at 135°Cpsi and 60°C; - thermocouple, thermistor or
2011420-Disclosed herein are an asphalt concrete mixture, an asphalt binder composition, and methods of preparing the related compositions. The asph
2010326- bitumen, deasphlter rock, and heavy oils tar bitumen, crude oil, atmospheric or vacuum declined from 200 psi to as low as 30 psi
2010820- plastic, concrete, wood or asphaltic hot mix. and from 0-20% bitumen, yields a composition 4800±600 PSI, and the electrical resistan
graded type of mix known as hot rolled asphalt.bitumen (60/70 pen, or 40/50 pen if avafPSI = 2.0 AASHTO /: / / L= 0.5 PSI =
asphalt, asphaltenes and bitumen; contacting the tar sands involve the use of hot water, organica pressure from about 500 to about 5,000 psi
2011720-A device for producing small-scale batches foamed bitumen. The device has a first pressurized, holding chamber for heating bitumen to a sele
mm Rutting in Specimens Tested by ASTEC Asphalt psi Properties of Steady State Region of Creep (to the Aggregate or to the Bitumen) Strongly
at a pressure of, for example, about 1600 psi Cooling Effusion 3.00 5.00 12.5 600 20.0 tar sands, shale oil, bitumen, and methane
